1.5 inch Pool Hose for Intex Filter Pump - 29060E Pool Hoses for
✅ PROS
- Pre-attached screw collars fit Intex 1.5 inch " filter pumps and sand filters without extra adapters or clamps
- Reinforced ribbed construction resists kinking and crushing better than thin-wall generic hoses
- Sold in a 2-pack — you get both the inlet and outlet hoses for the price of one
❌ CONS
- Length is fixed at 3 feet each; longer runs require splicing or buying additional connectors
- Collars are plastic and can crack if over-tightened with pliers instead of hand-tightened
The Verdict
If you own an Intex pool with a filter pump, you already know the drill: the original hoses get brittle, crack at the collar, or just plain wear out after a season. The 1.5" Pool Hose for Intex Filter Pump (model 29060E) is a direct replacement that promises to fix that problem. At 4.4 stars from 220 buyers, it’s clearly doing something right. Here’s the full story.
What You Actually Get
This listing ships as a 2-pack of 3-foot hoses, each with the ribbed, corrugated construction Intex uses on their factory equipment. The key detail is the pre-attached screw collars — these thread directly onto your Intex filter pump’s inlet and outlet ports with zero additional fittings. You don’t need hose clamps, Teflon tape, or adapters. It’s genuinely plug-and-play.
The hose diameter is a true 1.5-inch, matching the standard Intex port size. As shown in the product image, the collars have molded grip ridges, which makes hand-tightening actually feasible — a small but appreciated design touch.
Real-World Performance
I’ve tested these against both the OEM Intex hose and a cheap no-name alternative. The construction is noticeably sturdier than the bargain-bin options: the ribbed walls are thicker and hold their shape even when the pump vibrates or the hose bends around a corner. One buyer put it simply: “These are exactly like the original Intex hoses, maybe a bit stiffer. They connected in seconds.”
The screw collars seal well when hand-tightened. I ran my pump for two days straight with no leaks at the connection points. The internal bore is smooth enough that water flow isn’t noticeably restricted compared to the factory hose — important for keeping your pump’s flow rate where it needs to be for proper skimming.
What Buyers Praise
The dominant theme in customer feedback is fit and simplicity. Multiple reviewers mention they were skeptical about aftermarket parts, but these worked flawlessly. One typical review: “I ordered these as a replacement for my Intex 637R pump. They fit perfectly, no leaks, and the price was better than buying OEM.” The 2-pack value also gets frequent shout-outs — you’re replacing both hoses at once, which makes sense since they tend to fail at similar times.
Where It Falls Short
The 3-foot length is limiting. If your pump sits more than a few feet from your pool’s wall, you’ll need to extend these, which requires additional connectors or a longer single hose. This is fine for standard above-ground setups where the pump mounts right at the pool edge, but it’s a real constraint for anything unconventional.
The plastic collars are the weak point. They’ll hold up fine under normal hand-tightening, but I’ve seen reports of users cracking them by using pliers to force a tighter seal. Treat them like hand-tight-only fittings. Also, while the hose is flexible, it’s not soft — in cold weather (below 50°F), it stiffens noticeably and becomes harder to route around tight corners.
Who Should Buy This
- Intex above-ground pool owners with a 1.5" filter pump (models like 56601EG, 637R, 28692EG) who need a direct, no-modification replacement
- DIY pool maintainers who want a spare set on hand; the 2-pack means you’re covered for a full season or two
- Budget buyers who don’t want to pay OEM prices for what is functionally the same part
Skip it if you need a hose longer than 3 feet for your run, or if you have a non-Intex pump with different port sizes — this is specifically designed for Intex threading.
FAQ
Q: Will this fit my Intex sand filter pump? A: Yes, if your pump uses 1.5" threaded ports — which covers most Intex sand filter models. Check your pump’s port diameter before ordering; if it’s 1.25", this won’t fit.
Q: Can I use these with a non-Intex pump? A: The threading is Intex-specific. Other brands use different port sizes and thread patterns, so these likely won’t seal properly without adapters. Stick with Intex equipment.
Q: How long do these hoses last compared to OEM? A: Under normal summer use (UV exposure, chemical exposure, pumping), expect 1-2 seasons. The plastic collars are the first thing to fail, so store the hoses indoors during winter to extend their life.
The Verdict
Buy it if you need a direct, hassle-free replacement for your Intex filter pump hoses and want the convenience of a 2-pack at a fair price. It’s a solid, functional upgrade over worn-out factory parts.
Skip it if you need a custom-length run, or if you’re the type who grabs pliers to tighten fittings — the plastic collars won’t forgive you.
Rating: 4.2/5 — It does exactly what it claims, with minor compromises on length and collar durability. For the price and the fit, it’s the smart choice for most Intex pool owners.
Where to Buy
We earn a small commission at no extra cost to you — this helps fund more honest reviews.
Last updated: 2026-08-06. Ratings and prices current as of review date. Verify on Amazon before purchasing.